This is a step by step blow of a rebuild of a dead Wing I got a few months back. Bear with me as I experiment with the site and make it a informative as can. If you have any suggestions on what I am doing please feel free to add your comments or contact me directly.
Friday, February 19, 2010
Hows this for an oil flter conversion?
Got a oil filter conversion plate for the Goldwing. It allows me to use the off the shelf oil filters. Makes for a real easy oil change. Polished it out and threw a filter on it. I'll run it for about 2 hours total time and change the oil out to make sure its clean in the engine. Then the good stuff.


Exhaust, exhaust... what do I do?
Well I got her out the other day for the first start since the rebuild/restoration/customnization. Filled her with oil and antifreeze. Gave a few dead cranks to get the oil moving, a shot of starting fluid and BAM running like a champ. I have started her a few times since then just to hear her pur and its an easy task.... starts right up. Puts my mind at ease to because it further gives credibility to my carb rebuilding skills. NOW THE EXHAUST! Well being out of work has left me in a little predicament. I cant fabricate the exhaust I wanted to so I am left with using the stock exhaust for the time being. I will modify that. Not sure what I will do as the chrome is pretty well hammered but the overall condition of the exhaust is good... maybe black it out. Pictures below....




Friday, February 12, 2010
She's getting there....
Well it was 47 degrees out to day and some what sunny so I figured I wheel out the beast. Still afew little things to do and I will crank her up this weekend. Waiting on the painted parts, the exhaust has to be fabricated, the dual lights have to mounted once I create a bracket for it (It will look cool) then signal and tail lights. Waiting till the last for those as I have to cut down the rear fender ALOT and I cant d that till I get the seat back. Seat is custom so I dont want to pre cut anything and be wrong. Well here she is.....

Wednesday, February 3, 2010
Cutting down the Clutch and Throttlecables.
After putting on the drag bars I didnt take into consideration that my cables would be longer, like 6 inches to long because the stock bars sat that much higher. So it was off to my local cycle shop to have the cables trimmed back. When I got there I talked to the mechanic and h said as long as I had a dremel with a cutting wheel and a soldering iron I could easily do it myself. I dont mind a challenge so 6 bucks in parts and a couple hours later he was right. One of the easiest tasks I have done working on this beast.


Monday, February 1, 2010
Houston we have ignition.... well we have juice but no fire yet.
Had a small problem with the electrics the other day... no juice. Traced it all the way back to the solenoid next to the battery. Replaced it and bingo we have power. Engine turns and everything. I still need to get the carbs checked over before I mount them in, once that happens I can fire her up. I cant wait, one thing at a time. Mounted up the kick stand and rear brake assembly, all cleaned up and buffed out. The pictures dont do it justice as the pictures I take tend to produce more dust on the bike than actually exists it seems. Also went to installed the cable for the clutch and it seems ALL my cables need to be trimmed back about 3 or 4 inches because of the drag bars I put on are alot shorter. I will do those myself tomorrow. Exciting day as I actually took the bike off the stand and sat it on its on kick stand.... we are almost there.



Friday, January 29, 2010
The electrics gets some time and the Instrument Cluster goes on..... Turn the key and nothing.
Well its amazing how much time passes when your busy. My poor baby has been sitting patiently waiting for me to spend some quality time with her. Its been hard cash being tight and my attentions being drawn elsewhere, but she is here and patiently waits. During one of my many passes through my end of the garage to take the dogs out to do there duty the guilt of the Goldwing sitting there finally got ahold of me. I got the dogs in and pulled the cover off the bike and started working away and told myself nothing gets in the way today. This is what I did.....



Shock work to!
Oh and I almost forgot! I got my stainless steel bushing in for the rear shocks. I needed to have them machined to fit the shocks from a 2009 Honda VTX. The shocks were a bit wider than the stock 1980 Goldwing shocks so I needed to bump them put about 3/8ths of an inch on both sides to clear the frame. The shock studs were wide enough to accommodate the adjustment. The bushings went on the inside of the shock mount, nylon spacers went on the opposite side for a snug squeak free fit. Worked out well. Bolts and stuff still need the polish but the first run pre-fit went well. Check out the pictures.



Well its amazing how much time passes when your busy. My poor baby has been sitting patiently waiting for me to spend some quality time with her. Its been hard cash being tight and my attentions being drawn elsewhere, but she is here and patiently waits. During one of my many passes through my end of the garage to take the dogs out to do there duty the guilt of the Goldwing sitting there finally got ahold of me. I got the dogs in and pulled the cover off the bike and started working away and told myself nothing gets in the way today. This is what I did.....
Shock work to!
Oh and I almost forgot! I got my stainless steel bushing in for the rear shocks. I needed to have them machined to fit the shocks from a 2009 Honda VTX. The shocks were a bit wider than the stock 1980 Goldwing shocks so I needed to bump them put about 3/8ths of an inch on both sides to clear the frame. The shock studs were wide enough to accommodate the adjustment. The bushings went on the inside of the shock mount, nylon spacers went on the opposite side for a snug squeak free fit. Worked out well. Bolts and stuff still need the polish but the first run pre-fit went well. Check out the pictures.
Tuesday, September 8, 2009
Tank in, Wiring harness on, Brake lines on.... its coming together
Well I finally got a Labor Day run at the project and had a productive day. I got the new/used coils in on Friday so I thought it would be a good time to get the harness in. I started my scrubbing the harness down and taking the components off the mounting bracket. The bracket was painted and mounted on the bike, thusly the components went back on. Once I got the harness in and mounted I proceeded to cleanup the coils and the mounting brackets.... thats going to take a bit as all the mounting screws are frozen (They will go in later). Disasembled the rear wheel one more time to get the gas tank in. Nice powder coated tank! Then proceeded to cleanup the brake lines and reinstalled those. Then the battery box and battery. Its getting there folks. I'll get the coils done this week and mounted in.... it will all look new. Enjoy the pictures.
Subscribe to:
Posts (Atom)