Thursday, November 20, 2008



These pictures show the swingarm mounted on the frame and the drive shaft installed.  Looks like there is a ton of room.  I think I can gain a total of 1.5 inches of room for a larger tire.  I will test it farther by moving the swingarm in different positions to see where it could possibly rub then I will have the new patch welded on the swingarm.  Once thats done its off to the powder coating shop for the finish, install the new bearing then on the frame.


Here you see I have cut away the factory welded indentation to expose the drive tube. Notice how thick the piece was.  The reason for the thickness os the overlap of materials in that corner of the swingarm.  Just cutting away the top layer would not hinder the performance/strength of the swingarm in anyway and would allow for a minor upgrade to larger tire without having to go through the extreme process I am now.  Something to think about if you want to do a quick tire upgrade.

Swingarm modification


In these photos I have started the modifications for the swingarm to accomodate a bigger tire.

Tuesday, November 18, 2008

Swingarm pictures coming next!

Thursday, November 13, 2008



Here are a few more pictures of the engine installed.
Posted by Picasa


Here we have the engine being mounted in the frame. Before this was done the clutch and timing belts were replaced as well as all the case bolts replaced with stainless allen head bolts. I'll show a close up of those in the next picture. They really dress up the engine next to the buffed out timin and valve covers.
Posted by Picasa

Here is the engie now primed and painted. I kept it the original color and used Duplicolor engine Primer and paint. I put the old valve covers on as they were trashed from sitting out in the weather for so long but they served to make great paint covers. It was much easier than taping. On the front view I cleaned and buffed out the original timing belt covers as they were protected from weather, rocks and bugs under the full fairing. They came out nice. You can see the buffer out valve covers later in the engine installations pictures.
Posted by Picasa

The engine has now been degreased and I am getting ready to scotch brite it to prep it for primer and then paint.
Posted by Picasa

Here is the newer engine. The original engine was toast when the valves broke and embedded themselves into the pistons. This engine has half the miles and it looked great. My son found this sitting in the basement of some guys house across the country. Here I am getting ready to start the cleaning process.
Posted by Picasa

I had the gas tank powder coated also even though I was advised against it. The problem as told to me was when the tank go into the furnace after the powder coating is applied the goose necks usually have a lead solder attaching them to the tanks them selves and they usually can't take the heat and melt. In my case the goose neck was welded not soldered hence it can take the heat. I used the bench buffer to restore the gas cap and pickup.
Posted by Picasa

Triples before I mounted the forks.
Posted by Picasa

Here are the forks polished and assembled with new seals and boots. The triples have also been powder coated, new bearings the works. Like I said before its amazing what a good bench buffer can do for old parts.


Posted by Picasa

Wednesday, November 12, 2008


Here we have the forks. As you see I started refinishing them. The orignal worn look on the left and the wet sanded buffed on the right. I worked them a bit more till I achieved the mirror finish you'll see later in newer pictures. One of the best purchases I made was a buffer/refinisher. I was able to clean up alotof stuff off this bike to a near new condition including bolts. Wait till you see these babies finish and hanging on the triples.
Posted by Picasa


Here we have the bike totally stripped now and powder coated. Man I love powder coating. This frame came out so nice. I have been working on the front forks while I waiting for the frame to come back.
Posted by Picasa


Still torn down yet farther. Having fun playing with a style for the handle bars, in this case stock Buell XB1200 bars flipped upside down. I kind of like it.
Posted by Picasa


Torn down a little farther now it pretty obvious I have decided to make this a project. A naked Goldwing is born. Here I place a seat off my sons Buell to get an idea of what I want to do with it.
Posted by Picasa

Well after not getting the starter to turn getting a loud clunk as I pressed the starter but this is what I found when I pulled the plug and even farther when I pulled the head. Without major work this engine has no become a parts motor. I was fortunate to have a persistence son that found another motor with low mileage for cheap money. You'll see the pictures of it later in the blog.
Posted by Picasa